Knowing Essential Plumbing Skills is Crucial For Installing a Bathtub

Free Quote

Are you in search of facts and techniques around Installing A Bathtub?

Setting up a tub isn't exactly rocket science, however it does require solid plumbing, woodworking, and also often, tiling abilities. Changing an old bath tub with a brand-new one is additionally a moderately challenging project. If the old bathtub is conveniently obtainable, the job can move speedily; if you need to open up a wall to eliminate the old bathtub and also position the new bathtub, the task is much harder. In either case, the project is within a residence handyman's abilities, although you will need a helper to leave the old tub as well as embeded in the brand-new one. Make sure you have actually qualified on your own for the work and fit trying it. Rather than working with a contractor to take over a halfway-completed task, it is far better to consider employing one before you start. Opportunities are you may need a professional plumber to make tube connections.
This write-up will certainly help you mount a new tub in your washroom if you have actually currently gotten a brand-new bathtub and do not require to transform the plan of your previous water supply pipelines.
Your tools and also material list should consist of the following:

New Tub

Hammer

Pipe Wrenches

Prybar

Shatterproof glass

Level

Pliers

Adjustable Wrench

Putty Blade

Screwdriver

Cold Knife

Tape Measure

Pipeline Caps

Removing Old Touches

If you need to change old taps with new ones as a part of your installation, then the first thing you should do is separate the water system. After doing so, activate the taps to drain any type of water continuing to be in the system. The process of getting rid of the existing taps can be rather problematic due to the restricted gain access to that is usually the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the taps. Have a fabric all set for the continuing to be water that will originate from the pipelines. As soon as the supply pipes have been eliminated, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from turning throughout this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any kind of old securing substance.
Prior to going on to fit the brand-new taps, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.

Fitting New Touches

If the tails of the brand-new taps are plastic, after that you will certainly need a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end offers a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the tap in the placing hole in the bath/basin making certain that the washing machines are in place between the faucet as well as the sink. Secure the tap in place with the manufacturer supplied backnut. When the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet connectors. The former kind should be linked to the tap ends first, tightening just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.

Mounting the Tub

Using both wooden boards under its feet, position the bath tub in the required placement. The wood boards are useful in equally spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 tiny points.
The next objective is to guarantee that the bathtub is leveled all round. This can be achieved by examining the spirit level as well as adjusting the feet on the bathtub till the spirit level reads level.
To install taps, fit the bottom of the furthest adaptable tap connector to the appropriate supply pipeline by making a compression join; after that do the same for the various other faucet.
Turn on the water supply as well as check all joints and also brand-new pipework for leakages and tighten them if needed. Fill up the bath tub and also examine the overflow outlet and also the typical outlet for leaks.
Lastly, repair the bath paneling as described in the manufacturer's instruction manual. Tiling and also sealing around the bathtub needs to wait until the bathtub has been utilized at the very least when as this will settle it into its final placement.

Getting ready for the Setup

Firstly, the supporting framework provided with the bathroom ought to be fitted (if called for) according to the maker's instructions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is essential to make sure that if the faucet features a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps system to prevent stress on the bath tub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you utilize all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its final placement.

Tiling Around the Bath tub

In the location where the bathroom satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to crack a stiff seal, triggering the water to permeate the wall in between the bathroom and also the tiling, leading to difficulties with moisture and also feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, as well as can securing gaps approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of drenched paper or soft rope. Remember to always fill up the bath tub with water prior to securing, to permit the activity experienced when the tub remains in usage. The sealant can split fairly very early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also easily readily available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or waterproof sticky and also grout.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

I came across that content on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while doing a lookup on the search engines. Sharing is good. You won't know, you may be helping someone out. Many thanks for your time. Visit us again soon.

Save your home, call now!